Most aerial lift breakdowns come from a short list of causes. Hydraulic leaks, batteries, control faults, worn pins and cables. Catch the first sign and it is a service call. Miss it and it is a machine down in the middle of a job.
AirWorx repairs boom lifts, scissor lifts and telehandlers in the field and in the shop, from Indianapolis, Fort Wayne, Warsaw and Flora. Here is what we see most, how to spot it early, and what to have ready when you call.
Before you call
Three things make the repair faster and the first part the right one.
- The serial number. It is on the data plate. It tells us the exact build. The serial number lookup guide shows where the plate is on each brand.
- The hours. On the hour meter. It tells us what service the machine is due for.
- What it is doing. Which function, from which controls, under what load, and when it started. A photo or a 10-second video of the problem saves a trip.
Then call the branch nearest the machine. Numbers are at the bottom of this page.
Boom lifts
Hydraulic leaks. The most common call. Cylinder seals, hose fittings, and holding valves. First sign: a wet spot under the machine, a boom that drifts down when parked raised, or a function that gets slow when the oil is warm. Hoses and fittings are usually a field repair. Cylinder work usually comes to the shop.
Platform control faults. Joysticks, foot switches, enable switches, and the control module. First sign: a function that works from the ground controls but not from the platform, or a function that cuts in and out. Usually a field repair once we have the serial number for the right part.
Boom cable wear on telescopic models. Extend and retract cables stretch and wear over time. Operators rarely notice until a boom hangs or chatters. Caught on inspection, measured against the manufacturer’s limit, and replaced in the shop.
Tilt and load sensor faults. First sign: alarms on level ground, or functions cutting out under a normal platform load. Often a calibration or a sensor swap in the field.
Engine and fuel on diesel units. Hard starts, stalling, smoke. Common after a machine sits over winter. Field diagnosis; repairs depend on the fault.
Scissor lifts
Batteries and chargers. The number one scissor lift call. First sign: a machine that will not make it through a shift, or a charger that never shows a full charge. Field repair in most cases.
Will not drive at height. Usually the pothole protection system or a limit switch. First sign: drives fine lowered, refuses to move once the platform is up. Field repair in most cases.
Platform settles when parked raised. Lift cylinder seal or a holding valve. First sign: the platform is lower in the morning than you left it. Cylinder work comes to the shop.
Side-to-side play at height. Worn scissor arm pins and bushings. First sign: the platform rocks when you move. Shop repair, and one to fix before it gets worse.
Tilt alarm on level ground. A tilt sensor out of calibration or a frame that is not sitting square. Field repair.
Telehandlers
Boom chatter or hang on extend and retract. Worn wear pads or boom chains. First sign: the boom moves in jerks or stops short. Adjustments can often be done in the field. Pad replacement usually comes to the shop.
Hydraulic leaks on lift and tilt cylinders. Same as booms: wet spots, drift, slow functions. Hoses in the field, cylinders in the shop.
Engine and fuel system faults. Hard starting, loss of power, fault codes. Common on machines that sat through the off-season. Field diagnosis first.
Load chart light coming on early. Frame level sensor or load moment indicator out of calibration, or outriggers not set. Field repair.
Transmission and drive faults. Slipping, no drive in one range, overheating. Shop repair.
Field or shop
A truck comes to you for: inspections, hoses and fittings, electrical and control faults, battery and charger work, sensor calibration, wheel seals, most diagnostics. You lose the machine for hours.
The machine comes to the shop for: cylinder reseals, boom cable replacement, pins and bushings, structural repair, engine and transmission work, anything that needs a hoist. Ask the branch about getting the machine in.
Not sure which? Call and describe the symptom. The branch will tell you.
What a repair visit looks like
- You call with the serial number, hours and the symptom.
- The branch quotes the diagnostic visit and books the truck or the pickup.
- The technician diagnoses, confirms the part, and quotes the repair before doing it.
- Repair done, machine tested, paperwork to you. If it was an inspection item, the inspection record is updated.
Keep it from happening again
The repairs above have one thing in common. They show up on a frequent or annual inspection before they stop a machine. A preventive maintenance plan schedules those inspections by hours and catches them on your calendar instead of the job’s. See the Annual Inspections guide for what is required and what gets checked.
Service by branch
| Branch | Service line |
|---|---|
| Indianapolis, IN | 317-471-1272 |
| Fort Wayne, IN | 260-247-2816 |
| Warsaw, IN | 574-268-9664 |
| Flora, IL | 618-662-8941 |
Main line: 1-833-424-7967. Urgent parts and support: 317-324-3878.
Questions people ask
Do you repair lifts you did not sell or rent?
Yes. Boom lifts, scissor lifts and telehandlers, wherever they came from.
Which brands do you service?
The brands we stock parts for, JLG, Genie, Skyjack, SkyTrak, Lull and Gradall, and most other aerial equipment.
Can you repair a lift on my jobsite?
Yes. Field service trucks run from all four branches. Repairs that need a hoist come to the shop.
My scissor lift will not drive when raised. What is wrong?
Most often the pothole protection system or a limit switch. It is a safety interlock, not a drive fault. Usually a field repair.
My boom drifts down when parked. Is it safe?
It is a leak in a cylinder or holding valve. Lower it, tag it, and call. Do not work from a platform that is settling.
How fast can you get a technician out?
Tell the branch a crew is waiting and they will get a truck out as fast as they can. Field service trucks run around the clock.
Do you keep parts in stock?
Common wear parts and filters are at the branch parts counters. Everything else ships to the branch or straight to you.
What do I need to have ready when I call?
Serial number, hours, and a description or video of the problem.
Have a machine down, or a symptom you want checked before it becomes one? Call the branch nearest the machine: Indianapolis 317-471-1272, Fort Wayne 260-247-2816, Warsaw 574-268-9664, Flora 618-662-8941. Or send the serial number, hours and symptom through the contact form.
Annual Inspections: What to Expect · Back to Equipment Resources
