Every boom lift, scissor lift and telehandler needs an annual inspection. Most need a frequent inspection in between. Skip either one and the machine should not be on a job.
AirWorx does both, in the shop or on your site, from Indianapolis, Fort Wayne, Warsaw and Flora. Here is what gets checked, how long it takes, and what happens when something fails.
Frequent vs annual: what the rules require
Aerial lifts fall under the ANSI A92 standards and OSHA’s aerial lift rules. Between them, they call for three kinds of inspection.
Pre-start inspection. The operator does this before each shift. Walk around the machine, check fluids, tires, controls, decals and safety devices. Takes a few minutes. No technician needed.
Frequent inspection. Required every three months or 150 hours of use, whichever comes first. Also required on any machine that has sat unused for more than three months. A qualified technician does this one. It is a shorter version of the annual.
Annual inspection. Required at least once every 13 months. A qualified technician inspects the whole machine against the manufacturer’s checklist, documents the results, and records any repairs. The machine gets an inspection record and a dated decal.
The annual is the one most fleets track. It is also the one a jobsite safety manager will ask to see.
What an annual inspection covers at AirWorx
Our technicians work from the manufacturer’s inspection checklist for the exact model. The list is long, but it breaks down into seven areas.
| Area | What we check |
|---|---|
| Structure | Boom sections, scissor arms, platform, welds, pins and bushings, wear pads, cracks and deformation |
| Hydraulics | Cylinders, hoses, fittings, pump, leaks, holding valves, fluid level and condition |
| Drive and tires | Drive motors, brakes, steering, tires and wheels, axle oscillation |
| Electrical | Batteries and charger, wiring, connectors, ground and platform controls, emergency stop and lowering |
| Safety devices | Tilt alarm, load sensing, limit switches, horn, lights, guardrails, gate, harness anchor points |
| Boom cables (telescopic booms) | Extend and retract cables and sheaves, inspected and measured to the manufacturer’s schedule, replaced when they reach their service limit |
| Decals and manuals | Capacity plate, safety decals, operator manual in the holder |
If the machine passes, it gets the inspection decal and the record goes in your file. If it does not, we tell you what failed, what it takes to fix, and whether it can run in the meantime.
How long it takes
Plan on a few hours on the machine for an annual inspection. A scissor lift goes faster than a large boom. Repairs found during the inspection add to that, depending on parts.
The busy months are March through May, when every machine needs to be ready at once. Book annuals in the winter and you are first in line, not waiting behind a fleet.
What it costs to skip it
An expired inspection is a jobsite problem before it is a machine problem. Safety audits ask for the record. A missing one can take the lift off the site that day. Insurance claims and incident investigations ask for it too.
The other cost is the repair you did not catch. Most of the failures on the next list start small and show up on an inspection months before they stop a machine.
Field service vs shop service
Field service. A service truck comes to your yard or jobsite. Good for annual and frequent inspections, hydraulic leaks, electrical faults, control problems, wheel seals, battery and charger issues, and most repairs that do not need a lift bay. You lose the machine for hours, not days.
Shop service. The machine comes to one of our four branches. Needed for structural repairs, major hydraulic work, boom cable replacement, engine work, and anything that needs the machine on a hoist or in a bay.
Not sure which one you need? Call the branch. Describe the symptom and they will tell you whether a truck can handle it.
What inspections catch before they become repairs
Most of the failures that stop a machine in season show up on an inspection months earlier. A cylinder seal that weeps a little. A joystick that sticks once in a while. A boom cable near its limit. Batteries that are losing a shift.
The inspection is where those get caught, quoted, and fixed on your schedule instead of the job’s. For the problems we see most on each type of machine, and what to do before you call, see the Aerial Lift Repair guide.
Preventive maintenance programs
A preventive maintenance plan schedules the frequent and annual inspections, fluid and filter changes, battery service and wear checks on a set interval, by hours or by season, matched to how hard the machine works.
Fleets on a plan have fewer in-season breakdowns for a simple reason. The small problems get found in a scheduled visit instead of on a Monday morning with a crew waiting.
Ask the branch about a PM plan for your fleet. It can be set up for one machine or forty.
Service by branch
| Branch | Service line |
|---|---|
| Indianapolis, IN | 317-471-1272 |
| Fort Wayne, IN | 260-247-2816 |
| Warsaw, IN | 574-268-9664 |
| Flora, IL | 618-662-8941 |
Main line: 1-833-424-7967. Urgent parts and support: 317-324-3878.
Questions people ask
How often does an aerial lift need an annual inspection?
At least once every 13 months, by a qualified technician, with a written record.
What is a frequent inspection?
A technician inspection every three months or 150 hours, whichever comes first, and after any three months of non-use.
Who can do an annual inspection?
A qualified person trained on that type of machine. For most fleets that means a dealer or service company technician.
Do you inspect lifts we did not buy or rent from you?
Yes. We inspect and service boom lifts, scissor lifts and telehandlers regardless of where they came from.
Can the inspection be done at my jobsite?
Yes. Field service trucks run from all four branches. Repairs that need a bay come to the shop.
What do I get when the inspection is done?
An inspection record for your file and a dated decal on the machine. Any failed items are listed with what it takes to fix them.
What happens if a machine fails?
We tell you what failed and quote the repair. If it is not safe to run, we tag it. If it is, we tell you what to watch until the repair is done.
How do I get the right part the first time?
Have the serial number ready. Our serial number lookup guide shows where the plate is on each brand.
Ready to book an annual or frequent inspection, or set up a preventive maintenance plan? Call the branch nearest the machine: Indianapolis 317-471-1272, Fort Wayne 260-247-2816, Warsaw 574-268-9664, Flora 618-662-8941. Or send the details through the contact form.
Aerial Lift Repair: The Problems We See Most · Browse Rentals · Back to Equipment Resources
